Image source: @hoodratsracingandtuning
The Painter's Tape Method: Your First Step to Ordering Strip Light Kits
Before ordering your Ultimate Underglow Strip Light Kit, it's essential to determine the correct sizes for your ride. The painter's tape method is a straightforward way to measure and ensure a perfect fit. By the end, you should have four strips of painter's tape to measure. For accurate sizing, divide the lengths of the front and rear tape pieces by two to get the correct LED strip size for each section. When applying your LED strips, apply only to clean, completely dry, plastic, or painted surfaces. Most undercoatings will not bond properly with the 3M adhesive.
Tools and Materials Needed:
- Measuring tape
- Painter's tape
Step-by-Step Guide to the Painter's Tape Method:
Step 1: Preparation
1. Gather Materials: Ensure you have a measuring tape and painter's tape.
Step 2: Mark the Strip Locations
1. Front Strips: Apply a single piece of painter's tape around the front bumper, about 2 inches from the edge of your ride. Ensure the tape follows the curves of the bumper for optimal light coverage to your tires.
2. Side Strips: Apply tape separately along the sides, keeping a 2-inch distance from the edge.
3. Rear Strips: Apply a single long piece of tape around the rear, following the bumper's curves or adjusting for custom parts for the best placement.
Step 3: Remove the Tape
1. Carefully Remove Tape: Delicately remove the painter's tape.
Step 4: Measure the Tape
1. Measure Lengths: Once the strips are removed, measure the length of each taped section.
Step 5: Record Your Measurements
1. Note Measurements: Record the lengths to determine the appropriate strip sizes for your order. Divide the lengths of the front and rear pieces of tape by 2 to get the correct measurements. When ordering, select 1 size for the 2 front strips, 1 size for the 2 side strips, and 1 size for the 2 rear strips.
Using the painter's tape method ensures you order the correct sizes, making the installation process smooth and accurate.
Ultimate Underglow Strip Light Kit Installation Guide
What Comes In The Box:
- (2) Front LED strips
- (2) Side LED strips
- (2) Rear LED strips
- Wiring harness
- Magic Controller box
- Zip ties and wire mounts
Tools and Materials Needed:
- Heat gun or hair blow dryer
- Cleaning supplies (degreaser, alcohol, and dry cloth)
Ultimate Underglow Strip Light Kit Installation Guide:
Step 1: Preparation and Testing
1. Unpack and Layout: Unpack all the LED strips from each reel and lay them out as they will be installed, starting with 2 strips in the front, 2 strips on the sides, and 2 strips in the rear. Note: Each reel package is labeled by size and location.
Step 2: Setting Up the Magic Controller Box
1. Using the Flathead: Use the included flathead screwdriver to loosen the metal clamps on the Magic Controller box.
2. Wire Connections: Connect the corresponding wires from the LED cable to the Magic Controller.
3. Connecting to Wiring Harness: Connect your Magic Controller to your wiring harness. Then connect your wiring harness to your ride's battery terminals to test your setup.
3. Mockup and Test: Ensure the arrows on the LED strips point toward the rear of your ride. Any incorrect arrow direction can result in malfunctioning lights.
Step 3: Setting Up the App
1. Download the App: Download the MagicLED app from Apple or Android.
2. Bluetooth Connection: Ensure your phone’s Bluetooth is on, open the app, and connect to "SP105E".
3. Configure Settings: Set the "Pixels" to "110" and choose "GRB WS2811" in the app settings. Browse the app to adjust colors, modes, speed, and brightness.
Step 4: Cleaning and Installation
Cleaning:
1. Wipe down grease and grime with any type of degreaser.
2. Wipe surface with alcohol.
3. Completely dry the surface. Apply only to clean, completely dry, plastic, or painted surfaces. On most undercoatings the adhesive will not adhere properly.
Attach Strips: Start with the front two strips. Peel off the 3M adhesive backing and apply the strip from the middle outwards, placing it about 2 inches from the edge of your ride. Make sure your curving your LED strips around the bumpers of your ride ensuring maximum light coverage.
Install Side and Rear Strips: Repeat the process for the side and rear strips. For custom rear bumpers, plan ahead and adjust accordingly.
Step 5: Running Wires and Final Steps
1. Route Wires: Run the wires from the engine bay to the strips, securing them with zip ties, and cable management mounts, keeping them away from hot or moving parts.
2. Heat Cure: Use a heat gun or blow dryer to cure the 3M adhesive to your ride. Keep the gun roughly 4-5 inches away from the strips at medium-high heat. If you see any bubbling in the clear silicon or adhesive hold the gun further away.
By following this step-by-step guide, you can confidently install our Ultimate Underglow Strip Light Kits on your ride, enhancing its appearance and visibility. For more information and to explore our products, visit our Ultimate Underglow Strip Light Kit.
Rubber Strip Hider For Underglow LED Strips Installation Guide
Our Rubber Strip Hider Roll:
Our 30ft roll of Rubber Strip Hider offers an effective and affordable solution for concealing your Underglow LED strips, priced at just $29. Don't let exposed LEDs spoil the beauty of your ride. This product ensures your hard work in achieving a stunning Underglow look isn't undermined. It shields the LED strips from view, preserving the flawless appearance you desire.
Installation Steps:
- Preparation: Clean the mounting surface thoroughly using a degreaser or alcohol to remove any residue and completely dry.
- Application: Apply the Rubber Strip Hider about 1 inch away from your LED strips and about 1 inch away from the edge of your ride.
- Custom Fit: Easily cut to your desired length using sharp scissors.
- Post-Heat: Apply heat with a heat gun or blow dryer to the installed rubber trim to ensure a secure and lasting bond with the 3M adhesive. This step is crucial for optimal performance.
Enhance your ride's look even further with our 30ft Rubber Strip Hider, eliminating visible LED strips whether parked or driving. Don't let exposed LEDs spoil your hard work in achieving a stunning look!
By following this step-by-step guide, you can confidently install our Ultimate Underglow Strip Light Kits and Rubber Strip Hider on your ride, enhancing its appearance and visibility. For more information and to explore our products, visit our Ultimate Underglow Strip Light Kit.
